D – 13 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and. All the Controls products ASTM D standard. Enter now!. 26 Nov ASTM D Method C. Reference. Uniaxial Compressive Strength of Intact Rock Core Specimens. (deg). Type. Failure Mode. Rock Type.
|Published (Last):||16 December 2012|
|PDF File Size:||15.11 Mb|
|ePub File Size:||14.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
No other units of measurement are included in this standard.
The tests provide data in determining the strength of rock, namely: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but astm d7012 not provided as part of asrm standard. The elastic moduli for such rocks should be determined from unload-reload astm d7012 that are not covered by these test methods.
Link to Active This link will always route to the current Active version of the standard. Related Products Searching for related products The elastic astm d7012 Methods B and D are used to calculate the stress and deformation in astm d7012 structures.
Users of this standard are cautioned that compliance with Practice D does not in itself ensure reliable results. Method A, triaxial compression test, is commonly used to simulate astm d7012 stress conditions under which most underground rock masses exist. Thus the strength values determined are in terms of total stress, that is, are astm d7012 corrected for pore pressures.
Reliable results depend on many factors; Practice D provides a means for evaluating some of those astm d7012. Thus the strength values determined are in terms of total stress, that is, are not corrected for pore pressures. Follow us YouTube LinkedIn. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. astm d7012
The elastic moduli for such rocks should be determined from unload-reload cycles that are not covered by these test methods. Rock mechanics – Accessories for uniaxial and triaxial tests: Register or Log in for direct access to additional content. Elastic moduli measured by sonic methods Test Method D may often be employed as a preliminary measure of anisotropy. Specimens of these astm d7012 possess specific mechanical resonant frequencies atm are determined by astm d7012 elastic modulus, mass, and geometry asttm the test specimen.
Deformation and strength of astm d7012 are known to be functions of confining pressure. Methods A and B determine the triaxial compressive strength at d77012 pressures and Methods C and D determi Agencies that meet the criteria of Practice D are generally astm d7012 capable of competent and objective testing. Temperature Variation— Applies to any of the methods and allows for testing at temperatures above or below astm d7012 temperature.
Therefore, laboratory values for intact specimens must be employed with proper judgment in engineering applications. It is desirable to conduct tests in the plane of foliation, cleavage or bedding and at right angles to it to determine the degree of anisotropy.
The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and astm d7012 suitability of the equipment and facilities used. Astm d7012 the triaxial mode, a water pressure gradient may d7102 applied to the specimen Note 1 Elastic moduli measured by sonic methods Test Method D may often be employed as preliminary measures of anisotropy.
However, there are some cases where either the rock type or the loading condition of astm d7012 problem under consideration will require the effective stress or drained parameters be determined. Method A, triaxial compression test, is commonly used to simulate the stress conditions under which most underground rock masses exist. D702 to Active This link will always route to the current Active version of the standard. The test method specifies the qstm, instrumentation, and procedures for determining the stress-axial strain and the stress-lateral strain curves, as well as Young’s modulus, Eand Poisson’s ratio.
Reliable results depend on many factors; Practice D provides a means for evaluating some of those factors. The original four standards are now referred to astm d7012 Methods in this qstm. These methods make no provision for astm d7012 pressure astm d7012 and specimens are undrained platens are not vented.
ASTM D, Test equipment Controls
Therefore, the dynamic elastic p Astm d7012 required, the hardness verification is performed with certified instruments.
The Rock core should have a diameter from Active view current version of standard. Temperature Variation-Applies to any of the methods and allows for testing at temperatures above or adtm room temperature. It is the responsibility of the astm d7012 of this standard to establish appropriate safety and health astm d7012 and determine the applicability of regulatory limitations prior to use.
The original four standards are now referred to as Methods in this standard.